Pre-order 1kg neoPLA Filament 1.75mm – Aurora Pink

Eligible for FREE SHIPPING

$29.99 CAD

Sold Out

BotFeeder neoPLA Filament Aurora Pink 1.75mm

Caution! This intense pink will bring you into the center of attention in the public.

  1. Brand: BotFeeder
  2. Material: neoPLA
  3. Diameter: 1.75mm
  4. Colour: Aurora Pink
  5. Filament Weight: 1kg
  6. SKU: 0000
  7. Made in: Taiwan


  1. Material Grade: NatureWorks 4032D
  2. Diameter Tolerance: +/- 0.03mm
  3. Roundness Tolerance: +/- 0.05mm
  4. Spool Length x Width: 190mm x 85mm
  5. Spool Hole Diameter: 38mm


Tricks & Tips

At BotFeeder we have a well equipped 3D printing studio with a lot of popular 3D printers. We know our materials will give you excellent results and to help you get these results here are tips and trick for using BotFeeder 3D printing filament.

  1. Extrusion Temperature: 190 to 210C
  2. 3D Print Speed: 15 to 100mm/sec
  3. Print Bed Temperature: 60 to 70C
  4. Layer Thickness: 0.05mm or higher
  5. Nozzle Size: 0.1mm or higher

Build Platform:
For BotFeeder neoPLA we advice to print on a heated bed. After printing, the build plate needs to cool down to about 20-30 C at which point you can remove the printed part.

In the Box

  1. 1 x 1kg of BotFeeder neoPLA 1.75mm Aurora Pink Filament
  2. 1 x BotFeeder spool holder
  3. 1 x A pack of large desiccant
  4. 1 x Vacuumed sealed bag


Filament Care Tips

Storing Your Filament

Please note that improper storage may damage your filament. To maintain its original quality, it's strongly recommended that the filament be stored in the following conditions:

  • A dehumidifier cabinet or a dry and circulated area
  • Room temperature
  • Avoid direct sunlight or heat source

Selecting A Printer Location

Please note poor printer location will have a negative effect on your print result and possible of damaging your filament. To select the most ideal location for your printer, please follow this guide.

  • Consistent temperature
  • Stable air flow
  • Away from furniture for safety

Avoid Tangling Your Filament

When unpacking, changing filament or unloading, It is strongly suggested to get a good grip at the end of the filament at all times in order to prevent tangling. The spool holder is specifically designed with 2 holes of each side, allowing you to secure the end of the filament by threading into it. or you can simply 3D print a "Filament clip" that is attached to the spool holder itself.

BotFeeder ABS Colour Code & Filament Tracker

If Filament Gets Damp

Dry it slowly in room temperature. Please note that heat drying the filament will damages its quality by making it become brittle. The preferred method of drying your filament is to put in a dehumidifier cabinet or in an airtight bag with a few packs of desiccants. It's recommended to maintain a humidity level of 25% or less.


In-House Production

All BotFeeder 3D Printer Filaments are produced in our own production facility, situated in the Taiwan. Since no external parties are involved in the making of BotFeeder filament we can ensure consistent quality on every order.

Excellent Diameter Tolerance

An important machine in our production are the laser measurement systems used to check the diameter of our filament real time during production. It’s measured over 1000 times per second and helps us guarantee that each spool of BotFeeder 3d printing filament produced within tolerance. We can guarantee 0.03mm +/- on both 2.90mm and 1.75mm BotFeeder 3D Printer Filament, which means you can rest assured that your printer is extruding the exact amount of material.


Within minutes of production a spool of BotFeeder 3d printing filament is wrapped with a protective film and then sealed airtight with a double barrier foil. To ensure minimal moisture, we upgraded to a large pack of desiccant.  To go the extra mile, we’ll also seal the fancy cardboard box that we use to ship our product. You can make sure BotFeeder 3d printing filament is fresh and ready for 3d printing when you’re done unboxing.

BotFeeder Filament Protective Measures

BotFeeder Filament Packaging

In-House Testing

The BotFeeder Testlab features a wide range of popular 3D printers. We’re continuously testing on our 3D printers to keep checking the quality of the materials we produce and to develop exciting new materials for the maker community. If your not sure how to print with our materials on your 3D printer, please contact us at

The following printers are used in our lab

  • Ultimaker Original
  • Ultimaker 2
  • Makerbot Replicator 2X
  • Lulzbot Mini
  • Original Pursa I3
  • Solidoodle 3
  • UFO Standard (Delta & E3D hot-end)
  • Rapidbot 2
  • 3D Lounge PRO XL

Companies who are interested in having their 3D printer(s) featured in our testlab can contact us at

Enhanced Spool Holder

  1. Method: Drop from 1.2m in height
  2. Number of Drops : 10 drops
  3. Result: Passed

Drop Test from height of 1.2 meters


To take an extra step for your safety, BotFeeder 3D Printer Filaments are being tested on an annually basis by SGS. On top of that, all our filaments are manufactured in compliance of RoHS (Restriction of Hazardous Substances).

SGS Certification

Material Science

BotFeeder was founded as a brand of Liing Shian Colorant Manufacturer which have been active in the masterbatch, and pigment & chemical auxiliaries for the plastics processing industry. Our knowhow, network and partnerships is driving material innovations and quality. You can expect BotFeeder to keep on developing interesting new materials, which will be tested on a variety of printers to make sure it’ll get the job done.

    Hot Items
    700g PLA Filament 1.75mm – Silky Pearl White
    700g PLA Filament 1.75mm – Metallic Copper
    1kg PLA Filament 1.75mm – Light Tan (Skin)
    1kg ABS Filament 1.75mm – Gray
    1kg PLA Filament 1.75mm – Caramel