neoPLA

BotFeeder neoPLA Filament Piano White 1.75mm

  1. Brand: BotFeeder
  2. Material: neoPLA
  3. Diameter: 1.75mm
  4. Colour: Piano White
  5. Filament Weight: 1kg
  6. SKU: 0000
  7. Made in: Taiwan

BotFeeder PLA White Filament & BoFee Bear

Specifications

  1. Material Grade: NatureWorks 4032D
  2. Diameter Tolerance: +/- 0.03mm
  3. Roundness Tolerance: +/- 0.05mm
  4. Spool Length x Width: 190mm x 85mm
  5. Spool Hole Diameter: 38mm

BotFeeder PLA White Filament Dimension

Tricks & Tips

At BotFeeder we have a well equipped 3D printing studio with a lot of popular 3D printers. We know our materials will give you excellent results and to help you get these results here are tips and trick for using BotFeeder 3D printing filament.

  1. Extrusion Temperature: 190 to 210C
  2. 3D Print Speed: 15 to 100mm/sec
  3. Print Bed Temperature: 60 to 70C (Optional)
  4. Layer Thickness: 0.05mm or higher
  5. Nozzle Size: 0.1mm or higher

Build Platform:
For BotFeeder neoPLA we advice to print on a heated bed. After printing, the build plate needs to cool down to about 20-30 C at which point you can remove the printed part.

In the Box

  1. 1 x 1kg of BotFeeder neoPLA 1.75mm Piano White Filament
  2. 1 x BotFeeder spool holder
  3. 1 x A pack of large desiccant
  4. 1 x Vacuumed sealed bag

BotFeeder PLA White Filament in the Box

Filament Care Tips

Storing Your Filament

Please note that improper storage may damage your filament. To maintain its original quality, it's strongly recommended that the filament be stored in the following conditions:

  • A dehumidifier cabinet or a dry and circulated area
  • Room temperature
  • Avoid direct sunlight or heat source

Selecting A Printer Location

Please note poor printer location will have a negative effect on your print result and possible of damaging your filament. To select the most ideal location for your printer, please follow this guide.

  • Consistent temperature
  • Stable air flow
  • Away from furniture for safety

Avoid Tangling Your Filament

When unpacking, changing filament or unloading, It is strongly suggested to get a good grip at the end of the filament at all times in order to prevent tangling. The spool holder is specifically designed with 2 holes of each side, allowing you to secure the end of the filament by threading into it. or you can simply 3D print a "Filament clip" that is attached to the spool holder itself.

BotFeeder PLA Colour Code & Filament Tracker

If Filament Gets Damp

Dry it slowly in room temperature. Please note that heat drying the filament will damages its quality by making it become brittle. The preferred method of drying your filament is to put in a dehumidifier cabinet or in an airtight bag with a few packs of desiccants. It's recommended to maintain a humidity level of 25% or less.

Quality

In-House Production

All BotFeeder 3D Printer Filaments are produced in our own production facility, situated in the Taiwan. Since no external parties are involved in the making of BotFeeder filament we can ensure consistent quality on every order.

Excellent Diameter Tolerance

An important machine in our production are the laser measurement systems used to check the diameter of our filament real time during production. It’s measured over 1000 times per second and helps us guarantee that each spool of BotFeeder 3d printing filament produced within tolerance. We can guarantee 0.03mm +/- on both 2.90mm and 1.75mm BotFeeder 3D Printer Filament, which means you can rest assured that your printer is extruding the exact amount of material.

Packaging

Within minutes of production a spool of BotFeeder 3d printing filament is wrapped with a protective film and then sealed airtight with a double barrier foil. To ensure minimal moisture, we upgraded to a large pack of desiccant.  To go the extra mile, we’ll also seal the fancy cardboard box that we use to ship our product. You can make sure BotFeeder 3d printing filament is fresh and ready for 3d printing when you’re done unboxing.

BotFeeder Filament Protective Measures

BotFeeder Filament Packaging

In-House Testing

The BotFeeder Testlab features a wide range of popular 3D printers. We’re continuously testing on our 3D printers to keep checking the quality of the materials we produce and to develop exciting new materials for the maker community. If your not sure how to print with our materials on your 3D printer, please contact us at support@botfeeder.ca

The following printers are used in our lab

  • Ultimaker Original
  • Ultimaker 2
  • Makerbot Replicator 2X
  • Lulzbot Mini
  • Original Pursa I3
  • Solidoodle 3
  • UFO Standard (Delta & E3D hot-end)
  • Rapidbot 2
  • 3D Lounge PRO XL

Companies who are interested in having their 3D printer(s) featured in our testlab can contact us at support@botfeeder.ca

Enhanced Spool Holder

  1. Method: Drop from 1.2m in height
  2. Number of Drops : 10 drops
  3. Result: Passed

Drop Test from height of 1.2 meters

Certifications

To take an extra step for your safety, BotFeeder 3D Printer Filaments are being tested on an annually basis by SGS. On top of that, all our filaments are manufactured in compliance of RoHS (Restriction of Hazardous Substances).

SGS Certification

Material Science

BotFeeder was founded as a brand of Liing Shian Colorant Manufacturer which have been active in the masterbatch, and pigment & chemical auxiliaries for the plastics processing industry. Our knowhow, network and partnerships is driving material innovations and quality. You can expect BotFeeder to keep on developing interesting new materials, which will be tested on a variety of printers to make sure it’ll get the job done.

    Sold Out

    neoPLA Benefits

    1. Better Tearing

    Support materials are easier to snap off with less debris

    2. Tougher PLA

    Adopts brand new production procedures, increase material toughness, and consequently heightens the physical strength in print itself.

    3. Smooth & Glossy Print Finish

    With proper printer calibrations and parameter settings in the slicer software, neo-PLA promotes stable extrusion flow which in turn yields even layering and thus improve the overall exterior appeal.

    BotFeeder neoPLA Filament Jet Black 1.75mm

    The absolute favourite and must have for everyone’s filament portfolio; Standard Black. By far the most popular 3d printing colour in our portfolio. There’s something about black 3d prints that just make the parts look real nice. If you can’t decide on a colour than you’ll always have Standard Black to rely on.

    1. Brand: BotFeeder
    2. Material: neoPLA
    3. Diameter: 1.75mm
    4. Colour: Jet Black
    5. Filament Weight: 1kg
    6. SKU: 0160
    7. Made in: Taiwan

    BotFeeder PLA Black Filament & BoFee Bear

    Specifications

    1. Material Grade: NatureWorks 4032D
    2. Diameter Tolerance: +/- 0.03mm
    3. Roundness Tolerance: +/- 0.05mm
    4. Spool Length x Width: 190mm x 85mm
    5. Spool Hole Diameter: 38mm

    BotFeeder PLA Black Filament Dimension

    Tricks & Tips

    At BotFeeder we have a well equipped 3D printing studio with a lot of popular 3D printers. We know our materials will give you excellent results and to help you get these results here are tips and trick for using BotFeeder 3D printing filament.

    1. Extrusion Temperature: 190 to 210C
    2. 3D Print Speed: 15 to 100mm/sec
    3. Print Bed Temperature: 60 to 70C (Optional)
    4. Layer Thickness: 0.05mm or higher
    5. Nozzle Size: 0.1mm or higher

    Build Platform:
    For BotFeeder noePLA we advice to print on a heated bed. After printing, the build plate needs to cool down to about 20-30 C at which point you can remove the printed part.

    In the Box

    1. 1 x 1kg of BotFeeder neoPLA 1.75mm Jet Black Filament
    2. 1 x BotFeeder spool holder
    3. 1 x A pack of large desiccant
    4. 1 x Vacuumed sealed bag

    BotFeeder PLA Black Filament in the Box

    Filament Care Tips

    Storing Your Filament

    Please note that improper storage may damage your filament. To maintain its original quality, it's strongly recommended that the filament be stored in the following conditions:

    • A dehumidifier cabinet or a dry and circulated area
    • Room temperature
    • Avoid direct sunlight or heat source

    Selecting A Printer Location

    Please note poor printer location will have a negative effect on your print result and possible of damaging your filament. To select the most ideal location for your printer, please follow this guide.

    • Consistent temperature
    • Stable air flow
    • Away from furniture for safety

    Avoid Tangling Your Filament

    When unpacking, changing filament or unloading, It is strongly suggested to get a good grip at the end of the filament at all times in order to prevent tangling. The spool holder is specifically designed with 2 holes of each side, allowing you to secure the end of the filament by threading into it. or you can simply 3D print a "Filament clip" that is attached to the spool holder itself.

    BotFeeder PLA Colour Code & Filament Tracker

    If Filament Gets Damp

    Dry it slowly in room temperature. Please note that heat drying the filament will damages its quality by making it become brittle. The preferred method of drying your filament is to put in a dehumidifier cabinet or in an airtight bag with a few packs of desiccants. It's recommended to maintain a humidity level of 25% or less.

    Quality

    In-House Production

    All BotFeeder 3D Printer Filaments are produced in our own production facility, situated in the Taiwan. Since no external parties are involved in the making of BotFeeder filament we can ensure consistent quality on every order.

    Excellent Diameter Tolerance

    An important machine in our production are the laser measurement systems used to check the diameter of our filament real time during production. It’s measured over 1000 times per second and helps us guarantee that each spool of BotFeeder 3d printing filament produced within tolerance. We can guarantee 0.03mm +/- on both 2.90mm and 1.75mm BotFeeder 3D Printer Filament, which means you can rest assured that your printer is extruding the exact amount of material.

    Packaging

    Within minutes of production a spool of BotFeeder 3d printing filament is wrapped with a protective film and then sealed airtight with a double barrier foil. To ensure minimal moisture, we upgraded to a large pack of desiccant.  To go the extra mile, we’ll also seal the fancy cardboard box that we use to ship our product. You can make sure BotFeeder 3d printing filament is fresh and ready for 3d printing when you’re done unboxing.

    BotFeeder Filament Protective Measures

    BotFeeder Filament Packaging

    In-House Testing

    The BotFeeder Testlab features a wide range of popular 3D printers. We’re continuously testing on our 3D printers to keep checking the quality of the materials we produce and to develop exciting new materials for the maker community. If your not sure how to print with our materials on your 3D printer, please contact us at support@botfeeder.ca

    The following printers are used in our lab

    • Ultimaker Original
    • Ultimaker 2
    • Makerbot Replicator 2X
    • Lulzbot Mini
    • Original Pursa I3
    • Solidoodle 3
    • UFO Standard (Delta & E3D hot-end)
    • Rapidbot 2
    • 3D Lounge PRO XL

    Companies who are interested in having their 3D printer(s) featured in our testlab can contact us at support@botfeeder.ca

    Enhanced Spool Holder

    1. Method: Drop from 1.2m in height
    2. Number of Drops : 10 drops
    3. Result: Passed

    Drop Test from height of 1.2 meters

    Certifications

    To take an extra step for your safety, BotFeeder 3D Printer Filaments are being tested on an annually basis by SGS. On top of that, all our filaments are manufactured in compliance of RoHS (Restriction of Hazardous Substances).

    SGS Certification

    Material Science

    BotFeeder was founded as a brand of Liing Shian Colorant Manufacturer which have been active in the masterbatch, and pigment & chemical auxiliaries for the plastics processing industry. Our knowhow, network and partnerships is driving material innovations and quality. You can expect BotFeeder to keep on developing interesting new materials, which will be tested on a variety of printers to make sure it’ll get the job done.

      Sold Out

      BotFeeder neoPLA Filament Gray 1.75mm

      Perfect balance of black and white. A neutral colour that brings into harmony of your multi-coloured print.

      1. Brand: BotFeeder
      2. Material: neoPLA
      3. Diameter: 1.75mm
      4. Colour: Gray
      5. Filament Weight: 1kg
      6. SKU: 0000
      7. Made in: Taiwan

       

      Specifications

      1. Material Grade: NatureWorks 4032D
      2. Diameter Tolerance: +/- 0.03mm
      3. Roundness Tolerance: +/- 0.05mm
      4. Spool Length x Width: 190mm x 85mm
      5. Spool Hole Diameter: 38mm

       

      Tricks & Tips

      At BotFeeder we have a well equipped 3D printing studio with a lot of popular 3D printers. We know our materials will give you excellent results and to help you get these results here are tips and trick for using BotFeeder 3D printing filament.

      1. Extrusion Temperature: 190 to 210C
      2. 3D Print Speed: 15 to 100mm/sec
      3. Print Bed Temperature: 60 to 70C (Optional)
      4. Layer Thickness: 0.05mm or higher
      5. Nozzle Size: 0.1mm or higher

      Build Platform:
      For BotFeeder neoPLA we advice to print on a heated bed. After printing, the build plate needs to cool down to about 20-30 C at which point you can remove the printed part.

      In the Box

      1. 1 x 1kg of BotFeeder neoPLA 1.75mm Gray Filament
      2. 1 x BotFeeder spool holder
      3. 1 x A pack of large desiccant
      4. 1 x Vacuumed sealed bag

       

      Filament Care Tips

      Storing Your Filament

      Please note that improper storage may damage your filament. To maintain its original quality, it's strongly recommended that the filament be stored in the following conditions:

      • A dehumidifier cabinet or a dry and circulated area
      • Room temperature
      • Avoid direct sunlight or heat source

      Selecting A Printer Location

      Please note poor printer location will have a negative effect on your print result and possible of damaging your filament. To select the most ideal location for your printer, please follow this guide.

      • Consistent temperature
      • Stable air flow
      • Away from furniture for safety

      Avoid Tangling Your Filament

      When unpacking, changing filament or unloading, It is strongly suggested to get a good grip at the end of the filament at all times in order to prevent tangling. The spool holder is specifically designed with 2 holes of each side, allowing you to secure the end of the filament by threading into it. or you can simply 3D print a "Filament clip" that is attached to the spool holder itself.

      BotFeeder PLA Colour Code & Filament Tracker

      If Filament Gets Damp

      Dry it slowly in room temperature. Please note that heat drying the filament will damages its quality by making it become brittle. The preferred method of drying your filament is to put in a dehumidifier cabinet or in an airtight bag with a few packs of desiccants. It's recommended to maintain a humidity level of 25% or less.

      Quality

      In-House Production

      All BotFeeder 3D Printer Filaments are produced in our own production facility, situated in the Taiwan. Since no external parties are involved in the making of BotFeeder filament we can ensure consistent quality on every order.

      Excellent Diameter Tolerance

      An important machine in our production are the laser measurement systems used to check the diameter of our filament real time during production. It’s measured over 1000 times per second and helps us guarantee that each spool of BotFeeder 3d printing filament produced within tolerance. We can guarantee 0.03mm +/- on both 2.90mm and 1.75mm BotFeeder 3D Printer Filament, which means you can rest assured that your printer is extruding the exact amount of material.

      Packaging

      Within minutes of production a spool of BotFeeder 3d printing filament is wrapped with a protective film and then sealed airtight with a double barrier foil. To ensure minimal moisture, we upgraded to a large pack of desiccant.  To go the extra mile, we’ll also seal the fancy cardboard box that we use to ship our product. You can make sure BotFeeder 3d printing filament is fresh and ready for 3d printing when you’re done unboxing.

      BotFeeder Filament Protective Measures

      BotFeeder Filament Packaging

      In-House Testing

      The BotFeeder Testlab features a wide range of popular 3D printers. We’re continuously testing on our 3D printers to keep checking the quality of the materials we produce and to develop exciting new materials for the maker community. If your not sure how to print with our materials on your 3D printer, please contact us at support@botfeeder.ca

      The following printers are used in our lab

      • Ultimaker Original
      • Ultimaker 2
      • Makerbot Replicator 2X
      • Lulzbot Mini
      • Original Pursa I3
      • Solidoodle 3
      • UFO Standard (Delta & E3D hot-end)
      • Rapidbot 2
      • 3D Lounge PRO XL

      Companies who are interested in having their 3D printer(s) featured in our testlab can contact us at support@botfeeder.ca

      Enhanced Spool Holder

      1. Method: Drop from 1.2m in height
      2. Number of Drops : 10 drops
      3. Result: Passed

      Drop Test from height of 1.2 meters

      Certifications

      To take an extra step for your safety, BotFeeder 3D Printer Filaments are being tested on an annually basis by SGS. On top of that, all our filaments are manufactured in compliance of RoHS (Restriction of Hazardous Substances).

      SGS Certification

      Material Science

      BotFeeder was founded as a brand of Liing Shian Colorant Manufacturer which have been active in the masterbatch, and pigment & chemical auxiliaries for the plastics processing industry. Our knowhow, network and partnerships is driving material innovations and quality. You can expect BotFeeder to keep on developing interesting new materials, which will be tested on a variety of printers to make sure it’ll get the job done.

        Sold Out

        BotFeeder neoPLA Filament Coke Red 1.75mm

        1. Brand: BotFeeder
        2. Material: neoPLA
        3. Diameter: 1.75mm
        4. Colour: Coke Red
        5. Filament Weight: 1kg
        6. SKU: 0000
        7. Made in: Taiwan

         

        Specifications

        1. Material Grade: NatureWorks 4032D
        2. Diameter Tolerance: +/- 0.03mm
        3. Roundness Tolerance: +/- 0.05mm
        4. Spool Length x Width: 190mm x 85mm
        5. Spool Hole Diameter: 38mm

         

        Tricks & Tips

        At BotFeeder we have a well equipped 3D printing studio with a lot of popular 3D printers. We know our materials will give you excellent results and to help you get these results here are tips and trick for using BotFeeder 3D printing filament.

        1. Extrusion Temperature: 190 to 210C
        2. 3D Print Speed: 15 to 100mm/sec
        3. Print Bed Temperature: 60 to 70C (Optional)
        4. Layer Thickness: 0.05mm or higher
        5. Nozzle Size: 0.1mm or higher

        Build Platform:
        For BotFeeder neoPLA we advice to print on a heated bed. After printing, the build plate needs to cool down to about 20-30 C at which point you can remove the printed part.

        In the Box

        1. 1 x 1kg of BotFeeder neoPLA 1.75mm Coke Red Filament
        2. 1 x BotFeeder spool holder
        3. 1 x A pack of large desiccant
        4. 1 x Vacuumed sealed bag

         

        Filament Care Tips

        Storing Your Filament

        Please note that improper storage may damage your filament. To maintain its original quality, it's strongly recommended that the filament be stored in the following conditions:

        • A dehumidifier cabinet or a dry and circulated area
        • Room temperature
        • Avoid direct sunlight or heat source

        Selecting A Printer Location

        Please note poor printer location will have a negative effect on your print result and possible of damaging your filament. To select the most ideal location for your printer, please follow this guide.

        • Consistent temperature
        • Stable air flow
        • Away from furniture for safety

        Avoid Tangling Your Filament

        When unpacking, changing filament or unloading, It is strongly suggested to get a good grip at the end of the filament at all times in order to prevent tangling. The spool holder is specifically designed with 2 holes of each side, allowing you to secure the end of the filament by threading into it. or you can simply 3D print a "Filament clip" that is attached to the spool holder itself.

        BotFeeder PLA Colour Code & Filament Tracker

        If Filament Gets Damp

        Dry it slowly in room temperature. Please note that heat drying the filament will damages its quality by making it become brittle. The preferred method of drying your filament is to put in a dehumidifier cabinet or in an airtight bag with a few packs of desiccants. It's recommended to maintain a humidity level of 25% or less.

        Quality

        In-House Production

        All BotFeeder 3D Printer Filaments are produced in our own production facility, situated in the Taiwan. Since no external parties are involved in the making of BotFeeder filament we can ensure consistent quality on every order.

        Excellent Diameter Tolerance

        An important machine in our production are the laser measurement systems used to check the diameter of our filament real time during production. It’s measured over 1000 times per second and helps us guarantee that each spool of BotFeeder 3d printing filament produced within tolerance. We can guarantee 0.03mm +/- on both 2.90mm and 1.75mm BotFeeder 3D Printer Filament, which means you can rest assured that your printer is extruding the exact amount of material.

        Packaging

        Within minutes of production a spool of BotFeeder 3d printing filament is wrapped with a protective film and then sealed airtight with a double barrier foil. To ensure minimal moisture, we upgraded to a large pack of desiccant.  To go the extra mile, we’ll also seal the fancy cardboard box that we use to ship our product. You can make sure BotFeeder 3d printing filament is fresh and ready for 3d printing when you’re done unboxing.

        BotFeeder Filament Protective Measures

        BotFeeder Filament Packaging

        In-House Testing

        The BotFeeder Testlab features a wide range of popular 3D printers. We’re continuously testing on our 3D printers to keep checking the quality of the materials we produce and to develop exciting new materials for the maker community. If your not sure how to print with our materials on your 3D printer, please contact us at support@botfeeder.ca

        The following printers are used in our lab

        • Ultimaker Original
        • Ultimaker 2
        • Makerbot Replicator 2X
        • Lulzbot Mini
        • Original Pursa I3
        • Solidoodle 3
        • UFO Standard (Delta & E3D hot-end)
        • Rapidbot 2
        • 3D Lounge PRO XL

        Companies who are interested in having their 3D printer(s) featured in our testlab can contact us at support@botfeeder.ca

        Enhanced Spool Holder

        1. Method: Drop from 1.2m in height
        2. Number of Drops : 10 drops
        3. Result: Passed

        Drop Test from height of 1.2 meters

        Certifications

        To take an extra step for your safety, BotFeeder 3D Printer Filaments are being tested on an annually basis by SGS. On top of that, all our filaments are manufactured in compliance of RoHS (Restriction of Hazardous Substances).

        SGS Certification

        Material Science

        BotFeeder was founded as a brand of Liing Shian Colorant Manufacturer which have been active in the masterbatch, and pigment & chemical auxiliaries for the plastics processing industry. Our knowhow, network and partnerships is driving material innovations and quality. You can expect BotFeeder to keep on developing interesting new materials, which will be tested on a variety of printers to make sure it’ll get the job done.

          Sold Out

          BotFeeder neoPLA Filament Neon Orange 1.75mm

          1. Brand: BotFeeder
          2. Material: neoPLA
          3. Diameter: 1.75mm
          4. Colour: Neon Orange
          5. Filament Weight: 1kg
          6. SKU: 0000
          7. Made in: Taiwan

           

          Specifications

          1. Material Grade: NatureWorks 4032D
          2. Diameter Tolerance: +/- 0.03mm
          3. Roundness Tolerance: +/- 0.05mm
          4. Spool Length x Width: 190mm x 85mm
          5. Spool Hole Diameter: 38mm

           

          Tricks & Tips

          At BotFeeder we have a well equipped 3D printing studio with a lot of popular 3D printers. We know our materials will give you excellent results and to help you get these results here are tips and trick for using BotFeeder 3D printing filament.

          1. Extrusion Temperature: 190 to 210C
          2. 3D Print Speed: 15 to 100mm/sec
          3. Print Bed Temperature: 60 to 70C (Optional)
          4. Layer Thickness: 0.05mm or higher
          5. Nozzle Size: 0.1mm or higher

          Build Platform:
          For BotFeeder neoPLA we advice to print on a heated bed. After printing, the build plate needs to cool down to about 20-30 C at which point you can remove the printed part.

          In the Box

          1. 1 x 1kg of BotFeeder neoPLA 1.75mm Neon Orange Filament
          2. 1 x BotFeeder spool holder
          3. 1 x A pack of large desiccant
          4. 1 x Vacuumed sealed bag

           

          Filament Care Tips

          Storing Your Filament

          Please note that improper storage may damage your filament. To maintain its original quality, it's strongly recommended that the filament be stored in the following conditions:

          • A dehumidifier cabinet or a dry and circulated area
          • Room temperature
          • Avoid direct sunlight or heat source

          Selecting A Printer Location

          Please note poor printer location will have a negative effect on your print result and possible of damaging your filament. To select the most ideal location for your printer, please follow this guide.

          • Consistent temperature
          • Stable air flow
          • Away from furniture for safety

          Avoid Tangling Your Filament

          When unpacking, changing filament or unloading, It is strongly suggested to get a good grip at the end of the filament at all times in order to prevent tangling. The spool holder is specifically designed with 2 holes of each side, allowing you to secure the end of the filament by threading into it. or you can simply 3D print a "Filament clip" that is attached to the spool holder itself.

          BotFeeder PLA Colour Code & Filament Tracker

          If Filament Gets Damp

          Dry it slowly in room temperature. Please note that heat drying the filament will damages its quality by making it become brittle. The preferred method of drying your filament is to put in a dehumidifier cabinet or in an airtight bag with a few packs of desiccants. It's recommended to maintain a humidity level of 25% or less.

          Quality

          In-House Production

          All BotFeeder 3D Printer Filaments are produced in our own production facility, situated in the Taiwan. Since no external parties are involved in the making of BotFeeder filament we can ensure consistent quality on every order.

          Excellent Diameter Tolerance

          An important machine in our production are the laser measurement systems used to check the diameter of our filament real time during production. It’s measured over 1000 times per second and helps us guarantee that each spool of BotFeeder 3d printing filament produced within tolerance. We can guarantee 0.03mm +/- on both 2.90mm and 1.75mm BotFeeder 3D Printer Filament, which means you can rest assured that your printer is extruding the exact amount of material.

          Packaging

          Within minutes of production a spool of BotFeeder 3d printing filament is wrapped with a protective film and then sealed airtight with a double barrier foil. To ensure minimal moisture, we upgraded to a large pack of desiccant.  To go the extra mile, we’ll also seal the fancy cardboard box that we use to ship our product. You can make sure BotFeeder 3d printing filament is fresh and ready for 3d printing when you’re done unboxing.

          BotFeeder Filament Protective Measures

          BotFeeder Filament Packaging

          In-House Testing

          The BotFeeder Testlab features a wide range of popular 3D printers. We’re continuously testing on our 3D printers to keep checking the quality of the materials we produce and to develop exciting new materials for the maker community. If your not sure how to print with our materials on your 3D printer, please contact us at support@botfeeder.ca

          The following printers are used in our lab

          • Ultimaker Original
          • Ultimaker 2
          • Makerbot Replicator 2X
          • Lulzbot Mini
          • Original Pursa I3
          • Solidoodle 3
          • UFO Standard (Delta & E3D hot-end)
          • Rapidbot 2
          • 3D Lounge PRO XL

          Companies who are interested in having their 3D printer(s) featured in our testlab can contact us at support@botfeeder.ca

          Enhanced Spool Holder

          1. Method: Drop from 1.2m in height
          2. Number of Drops : 10 drops
          3. Result: Passed

          Drop Test from height of 1.2 meters

          Certifications

          To take an extra step for your safety, BotFeeder 3D Printer Filaments are being tested on an annually basis by SGS. On top of that, all our filaments are manufactured in compliance of RoHS (Restriction of Hazardous Substances).

          SGS Certification

          Material Science

          BotFeeder was founded as a brand of Liing Shian Colorant Manufacturer which have been active in the masterbatch, and pigment & chemical auxiliaries for the plastics processing industry. Our knowhow, network and partnerships is driving material innovations and quality. You can expect BotFeeder to keep on developing interesting new materials, which will be tested on a variety of printers to make sure it’ll get the job done.

            Sold Out

            BotFeeder neoPLA Filament Lemon Yellow 1.75mm

            This yellow reminds me the yellow tulip garden that I visit every year in May. An enjoyable afternoon with family and friends.

            1. Brand: BotFeeder
            2. Material: neoPLA
            3. Diameter: 1.75mm
            4. Colour: Lemon Yellow
            5. Filament Weight: 1kg
            6. SKU: 0000
            7. Made in: Taiwan

             

            Specifications

            1. Material Grade: NatureWorks 4032D
            2. Diameter Tolerance: +/- 0.03mm
            3. Roundness Tolerance: +/- 0.05mm
            4. Spool Length x Width: 190mm x 85mm
            5. Spool Hole Diameter: 38mm

             

            Tricks & Tips

            At BotFeeder we have a well equipped 3D printing studio with a lot of popular 3D printers. We know our materials will give you excellent results and to help you get these results here are tips and trick for using BotFeeder 3D printing filament.

            1. Extrusion Temperature: 190 to 210C
            2. 3D Print Speed: 15 to 100mm/sec
            3. Print Bed Temperature: 60 to 70C (Optional)
            4. Layer Thickness: 0.05mm or higher
            5. Nozzle Size: 0.1mm or higher

            Build Platform:
            For BotFeeder neoPLA we advice to print on a heated bed. After printing, the build plate needs to cool down to about 20-30 C at which point you can remove the printed part.

            In the Box

            1. 1 x 1kg of BotFeeder neoPLA 1.75mm Lemon Yellow Filament
            2. 1 x BotFeeder spool holder
            3. 1 x A pack of large desiccant
            4. 1 x Vacuumed sealed bag

             

            Filament Care Tips

            Storing Your Filament

            Please note that improper storage may damage your filament. To maintain its original quality, it's strongly recommended that the filament be stored in the following conditions:

            • A dehumidifier cabinet or a dry and circulated area
            • Room temperature
            • Avoid direct sunlight or heat source

            Selecting A Printer Location

            Please note poor printer location will have a negative effect on your print result and possible of damaging your filament. To select the most ideal location for your printer, please follow this guide.

            • Consistent temperature
            • Stable air flow
            • Away from furniture for safety

            Avoid Tangling Your Filament

            When unpacking, changing filament or unloading, It is strongly suggested to get a good grip at the end of the filament at all times in order to prevent tangling. The spool holder is specifically designed with 2 holes of each side, allowing you to secure the end of the filament by threading into it. or you can simply 3D print a "Filament clip" that is attached to the spool holder itself.

            BotFeeder PLA Colour Code & Filament Tracker

            If Filament Gets Damp

            Dry it slowly in room temperature. Please note that heat drying the filament will damages its quality by making it become brittle. The preferred method of drying your filament is to put in a dehumidifier cabinet or in an airtight bag with a few packs of desiccants. It's recommended to maintain a humidity level of 25% or less.

            Quality

            In-House Production

            All BotFeeder 3D Printer Filaments are produced in our own production facility, situated in the Taiwan. Since no external parties are involved in the making of BotFeeder filament we can ensure consistent quality on every order.

            Excellent Diameter Tolerance

            An important machine in our production are the laser measurement systems used to check the diameter of our filament real time during production. It’s measured over 1000 times per second and helps us guarantee that each spool of BotFeeder 3d printing filament produced within tolerance. We can guarantee 0.03mm +/- on both 2.90mm and 1.75mm BotFeeder 3D Printer Filament, which means you can rest assured that your printer is extruding the exact amount of material.

            Packaging

            Within minutes of production a spool of BotFeeder 3d printing filament is wrapped with a protective film and then sealed airtight with a double barrier foil. To ensure minimal moisture, we upgraded to a large pack of desiccant.  To go the extra mile, we’ll also seal the fancy cardboard box that we use to ship our product. You can make sure BotFeeder 3d printing filament is fresh and ready for 3d printing when you’re done unboxing.

            BotFeeder Filament Protective Measures

            BotFeeder Filament Packaging

            In-House Testing

            The BotFeeder Testlab features a wide range of popular 3D printers. We’re continuously testing on our 3D printers to keep checking the quality of the materials we produce and to develop exciting new materials for the maker community. If your not sure how to print with our materials on your 3D printer, please contact us at support@botfeeder.ca

            The following printers are used in our lab

            • Ultimaker Original
            • Ultimaker 2
            • Makerbot Replicator 2X
            • Lulzbot Mini
            • Original Pursa I3
            • Solidoodle 3
            • UFO Standard (Delta & E3D hot-end)
            • Rapidbot 2
            • 3D Lounge PRO XL

            Companies who are interested in having their 3D printer(s) featured in our testlab can contact us at support@botfeeder.ca

            Enhanced Spool Holder

            1. Method: Drop from 1.2m in height
            2. Number of Drops : 10 drops
            3. Result: Passed

            Drop Test from height of 1.2 meters

            Certifications

            To take an extra step for your safety, BotFeeder 3D Printer Filaments are being tested on an annually basis by SGS. On top of that, all our filaments are manufactured in compliance of RoHS (Restriction of Hazardous Substances).

            SGS Certification

            Material Science

            BotFeeder was founded as a brand of Liing Shian Colorant Manufacturer which have been active in the masterbatch, and pigment & chemical auxiliaries for the plastics processing industry. Our knowhow, network and partnerships is driving material innovations and quality. You can expect BotFeeder to keep on developing interesting new materials, which will be tested on a variety of printers to make sure it’ll get the job done.

              Sold Out

              BotFeeder neoPLA Filament Turquoise 1.75mm

              1. Brand: BotFeeder
              2. Material: neoPLA
              3. Diameter: 1.75mm
              4. Colour: Turquoise
              5. Filament Weight: 1kg
              6. SKU: 0000
              7. Made in: Taiwan

               

              Specifications

              1. Material Grade: NatureWorks 4032D
              2. Diameter Tolerance: +/- 0.03mm
              3. Roundness Tolerance: +/- 0.05mm
              4. Spool Length x Width: 190mm x 85mm
              5. Spool Hole Diameter: 38mm

               

              Tricks & Tips

              At BotFeeder we have a well equipped 3D printing studio with a lot of popular 3D printers. We know our materials will give you excellent results and to help you get these results here are tips and trick for using BotFeeder 3D printing filament.

              1. Extrusion Temperature: 190 to 210C
              2. 3D Print Speed: 15 to 100mm/sec
              3. Print Bed Temperature: 60 to 70C (Optional)
              4. Layer Thickness: 0.05mm or higher
              5. Nozzle Size: 0.1mm or higher

              Build Platform:
              For BotFeeder neoPLA we advice to print on a heated bed. After printing, the build plate needs to cool down to about 20-30 C at which point you can remove the printed part.

              In the Box

              1. 1 x 1kg of BotFeeder neoPLA 1.75mm Turquoise Filament
              2. 1 x BotFeeder spool holder
              3. 1 x A pack of large desiccant
              4. 1 x Vacuumed sealed bag

               

              Filament Care Tips

              Storing Your Filament

              Please note that improper storage may damage your filament. To maintain its original quality, it's strongly recommended that the filament be stored in the following conditions:

              • A dehumidifier cabinet or a dry and circulated area
              • Room temperature
              • Avoid direct sunlight or heat source

              Selecting A Printer Location

              Please note poor printer location will have a negative effect on your print result and possible of damaging your filament. To select the most ideal location for your printer, please follow this guide.

              • Consistent temperature
              • Stable air flow
              • Away from furniture for safety

              Avoid Tangling Your Filament

              When unpacking, changing filament or unloading, It is strongly suggested to get a good grip at the end of the filament at all times in order to prevent tangling. The spool holder is specifically designed with 2 holes of each side, allowing you to secure the end of the filament by threading into it. or you can simply 3D print a "Filament clip" that is attached to the spool holder itself.

              BotFeeder PLA Colour Code & Filament Tracker

              If Filament Gets Damp

              Dry it slowly in room temperature. Please note that heat drying the filament will damages its quality by making it become brittle. The preferred method of drying your filament is to put in a dehumidifier cabinet or in an airtight bag with a few packs of desiccants. It's recommended to maintain a humidity level of 25% or less.

              Quality

              In-House Production

              All BotFeeder 3D Printer Filaments are produced in our own production facility, situated in the Taiwan. Since no external parties are involved in the making of BotFeeder filament we can ensure consistent quality on every order.

              Excellent Diameter Tolerance

              An important machine in our production are the laser measurement systems used to check the diameter of our filament real time during production. It’s measured over 1000 times per second and helps us guarantee that each spool of BotFeeder 3d printing filament produced within tolerance. We can guarantee 0.03mm +/- on both 2.90mm and 1.75mm BotFeeder 3D Printer Filament, which means you can rest assured that your printer is extruding the exact amount of material.

              Packaging

              Within minutes of production a spool of BotFeeder 3d printing filament is wrapped with a protective film and then sealed airtight with a double barrier foil. To ensure minimal moisture, we upgraded to a large pack of desiccant.  To go the extra mile, we’ll also seal the fancy cardboard box that we use to ship our product. You can make sure BotFeeder 3d printing filament is fresh and ready for 3d printing when you’re done unboxing.

              BotFeeder Filament Protective Measures

              BotFeeder Filament Packaging

              In-House Testing

              The BotFeeder Testlab features a wide range of popular 3D printers. We’re continuously testing on our 3D printers to keep checking the quality of the materials we produce and to develop exciting new materials for the maker community. If your not sure how to print with our materials on your 3D printer, please contact us at support@botfeeder.ca

              The following printers are used in our lab

              • Ultimaker Original
              • Ultimaker 2
              • Makerbot Replicator 2X
              • Lulzbot Mini
              • Original Pursa I3
              • Solidoodle 3
              • UFO Standard (Delta & E3D hot-end)
              • Rapidbot 2
              • 3D Lounge PRO XL

              Companies who are interested in having their 3D printer(s) featured in our testlab can contact us at support@botfeeder.ca

              Enhanced Spool Holder

              1. Method: Drop from 1.2m in height
              2. Number of Drops : 10 drops
              3. Result: Passed

              Drop Test from height of 1.2 meters

              Certifications

              To take an extra step for your safety, BotFeeder 3D Printer Filaments are being tested on an annually basis by SGS. On top of that, all our filaments are manufactured in compliance of RoHS (Restriction of Hazardous Substances).

              SGS Certification

              Material Science

              BotFeeder was founded as a brand of Liing Shian Colorant Manufacturer which have been active in the masterbatch, and pigment & chemical auxiliaries for the plastics processing industry. Our knowhow, network and partnerships is driving material innovations and quality. You can expect BotFeeder to keep on developing interesting new materials, which will be tested on a variety of printers to make sure it’ll get the job done.

                Sold Out

                BotFeeder neoPLA Filament Sky Blue 1.75mm

                1. Brand: BotFeeder
                2. Material: neoPLA
                3. Diameter: 1.75mm
                4. Colour: Sky Blue
                5. Filament Weight: 1kg
                6. SKU: 0000
                7. Made in: Taiwan

                 

                Specifications

                1. Material Grade: NatureWorks 4032D
                2. Diameter Tolerance: +/- 0.03mm
                3. Roundness Tolerance: +/- 0.05mm
                4. Spool Length x Width: 190mm x 85mm
                5. Spool Hole Diameter: 38mm

                 

                Tricks & Tips

                At BotFeeder we have a well equipped 3D printing studio with a lot of popular 3D printers. We know our materials will give you excellent results and to help you get these results here are tips and trick for using BotFeeder 3D printing filament.

                1. Extrusion Temperature: 190 to 210C
                2. 3D Print Speed: 15 to 100mm/sec
                3. Print Bed Temperature: 60 to 70C (Optional)
                4. Layer Thickness: 0.05mm or higher
                5. Nozzle Size: 0.1mm or higher

                Build Platform:
                For BotFeeder neoPLA we advice to print on a heated bed. After printing, the build plate needs to cool down to about 20-30 C at which point you can remove the printed part.

                In the Box

                1. 1 x 1kg of BotFeeder neoPLA 1.75mm Sky Blue Filament
                2. 1 x BotFeeder spool holder
                3. 1 x A pack of large desiccant
                4. 1 x Vacuumed sealed bag

                 

                Filament Care Tips

                Storing Your Filament

                Please note that improper storage may damage your filament. To maintain its original quality, it's strongly recommended that the filament be stored in the following conditions:

                • A dehumidifier cabinet or a dry and circulated area
                • Room temperature
                • Avoid direct sunlight or heat source

                Selecting A Printer Location

                Please note poor printer location will have a negative effect on your print result and possible of damaging your filament. To select the most ideal location for your printer, please follow this guide.

                • Consistent temperature
                • Stable air flow
                • Away from furniture for safety

                Avoid Tangling Your Filament

                When unpacking, changing filament or unloading, It is strongly suggested to get a good grip at the end of the filament at all times in order to prevent tangling. The spool holder is specifically designed with 2 holes of each side, allowing you to secure the end of the filament by threading into it. or you can simply 3D print a "Filament clip" that is attached to the spool holder itself.

                BotFeeder PLA Colour Code & Filament Tracker

                If Filament Gets Damp

                Dry it slowly in room temperature. Please note that heat drying the filament will damages its quality by making it become brittle. The preferred method of drying your filament is to put in a dehumidifier cabinet or in an airtight bag with a few packs of desiccants. It's recommended to maintain a humidity level of 25% or less.

                Quality

                In-House Production

                All BotFeeder 3D Printer Filaments are produced in our own production facility, situated in the Taiwan. Since no external parties are involved in the making of BotFeeder filament we can ensure consistent quality on every order.

                Excellent Diameter Tolerance

                An important machine in our production are the laser measurement systems used to check the diameter of our filament real time during production. It’s measured over 1000 times per second and helps us guarantee that each spool of BotFeeder 3d printing filament produced within tolerance. We can guarantee 0.03mm +/- on both 2.90mm and 1.75mm BotFeeder 3D Printer Filament, which means you can rest assured that your printer is extruding the exact amount of material.

                Packaging

                Within minutes of production a spool of BotFeeder 3d printing filament is wrapped with a protective film and then sealed airtight with a double barrier foil. To ensure minimal moisture, we upgraded to a large pack of desiccant.  To go the extra mile, we’ll also seal the fancy cardboard box that we use to ship our product. You can make sure BotFeeder 3d printing filament is fresh and ready for 3d printing when you’re done unboxing.

                BotFeeder Filament Protective Measures

                BotFeeder Filament Packaging

                In-House Testing

                The BotFeeder Testlab features a wide range of popular 3D printers. We’re continuously testing on our 3D printers to keep checking the quality of the materials we produce and to develop exciting new materials for the maker community. If your not sure how to print with our materials on your 3D printer, please contact us at support@botfeeder.ca

                The following printers are used in our lab

                • Ultimaker Original
                • Ultimaker 2
                • Makerbot Replicator 2X
                • Lulzbot Mini
                • Original Pursa I3
                • Solidoodle 3
                • UFO Standard (Delta & E3D hot-end)
                • Rapidbot 2
                • 3D Lounge PRO XL

                Companies who are interested in having their 3D printer(s) featured in our testlab can contact us at support@botfeeder.ca

                Enhanced Spool Holder

                1. Method: Drop from 1.2m in height
                2. Number of Drops : 10 drops
                3. Result: Passed

                Drop Test from height of 1.2 meters

                Certifications

                To take an extra step for your safety, BotFeeder 3D Printer Filaments are being tested on an annually basis by SGS. On top of that, all our filaments are manufactured in compliance of RoHS (Restriction of Hazardous Substances).

                SGS Certification

                Material Science

                BotFeeder was founded as a brand of Liing Shian Colorant Manufacturer which have been active in the masterbatch, and pigment & chemical auxiliaries for the plastics processing industry. Our knowhow, network and partnerships is driving material innovations and quality. You can expect BotFeeder to keep on developing interesting new materials, which will be tested on a variety of printers to make sure it’ll get the job done.

                  Sold Out

                  BotFeeder neoPLA Filament Night Blue 1.75mm

                  1. Brand: BotFeeder
                  2. Material: neoPLA
                  3. Diameter: 1.75mm
                  4. Colour: Night Blue
                  5. Filament Weight: 1kg
                  6. SKU:000
                  7. Made in: Taiwan

                   

                  Specifications

                  1. Material Grade: NatureWorks 4032D
                  2. Diameter Tolerance: +/- 0.03mm
                  3. Roundness Tolerance: +/- 0.05mm
                  4. Spool Length x Width: 190mm x 85mm
                  5. Spool Hole Diameter: 38mm

                   

                  Tricks & Tips

                  At BotFeeder we have a well equipped 3D printing studio with a lot of popular 3D printers. We know our materials will give you excellent results and to help you get these results here are tips and trick for using BotFeeder 3D printing filament.

                  1. Extrusion Temperature: 190 to 210C
                  2. 3D Print Speed: 15 to 100mm/sec
                  3. Print Bed Temperature: 60 to 70C (Optional)
                  4. Layer Thickness: 0.05mm or higher
                  5. Nozzle Size: 0.1mm or higher

                  Build Platform:
                  For BotFeeder neoPLA we advice to print on a heated bed. After printing, the build plate needs to cool down to about 20-30 C at which point you can remove the printed part.

                  In the Box

                  1. 1 x 1kg of BotFeeder neoPLA 1.75mm Night Blue Filament
                  2. 1 x BotFeeder spool holder
                  3. 1 x A pack of large desiccant
                  4. 1 x Vacuumed sealed bag

                   

                  Filament Care Tips

                  Storing Your Filament

                  Please note that improper storage may damage your filament. To maintain its original quality, it's strongly recommended that the filament be stored in the following conditions:

                  • A dehumidifier cabinet or a dry and circulated area
                  • Room temperature
                  • Avoid direct sunlight or heat source

                  Selecting A Printer Location

                  Please note poor printer location will have a negative effect on your print result and possible of damaging your filament. To select the most ideal location for your printer, please follow this guide.

                  • Consistent temperature
                  • Stable air flow
                  • Away from furniture for safety

                  Avoid Tangling Your Filament

                  When unpacking, changing filament or unloading, It is strongly suggested to get a good grip at the end of the filament at all times in order to prevent tangling. The spool holder is specifically designed with 2 holes of each side, allowing you to secure the end of the filament by threading into it. or you can simply 3D print a "Filament clip" that is attached to the spool holder itself.

                  BotFeeder PLA Colour Code & Filament Tracker

                  If Filament Gets Damp

                  Dry it slowly in room temperature. Please note that heat drying the filament will damages its quality by making it become brittle. The preferred method of drying your filament is to put in a dehumidifier cabinet or in an airtight bag with a few packs of desiccants. It's recommended to maintain a humidity level of 25% or less.

                  Quality

                  In-House Production

                  All BotFeeder 3D Printer Filaments are produced in our own production facility, situated in the Taiwan. Since no external parties are involved in the making of BotFeeder filament we can ensure consistent quality on every order.

                  Excellent Diameter Tolerance

                  An important machine in our production are the laser measurement systems used to check the diameter of our filament real time during production. It’s measured over 1000 times per second and helps us guarantee that each spool of BotFeeder 3d printing filament produced within tolerance. We can guarantee 0.03mm +/- on both 2.90mm and 1.75mm BotFeeder 3D Printer Filament, which means you can rest assured that your printer is extruding the exact amount of material.

                  Packaging

                  Within minutes of production a spool of BotFeeder 3d printing filament is wrapped with a protective film and then sealed airtight with a double barrier foil. To ensure minimal moisture, we upgraded to a large pack of desiccant.  To go the extra mile, we’ll also seal the fancy cardboard box that we use to ship our product. You can make sure BotFeeder 3d printing filament is fresh and ready for 3d printing when you’re done unboxing.

                  BotFeeder Filament Protective Measures

                  BotFeeder Filament Packaging

                  In-House Testing

                  The BotFeeder Testlab features a wide range of popular 3D printers. We’re continuously testing on our 3D printers to keep checking the quality of the materials we produce and to develop exciting new materials for the maker community. If your not sure how to print with our materials on your 3D printer, please contact us at support@botfeeder.ca

                  The following printers are used in our lab

                  • Ultimaker Original
                  • Ultimaker 2
                  • Makerbot Replicator 2X
                  • Lulzbot Mini
                  • Original Pursa I3
                  • Solidoodle 3
                  • UFO Standard (Delta & E3D hot-end)
                  • Rapidbot 2
                  • 3D Lounge PRO XL

                  Companies who are interested in having their 3D printer(s) featured in our testlab can contact us at support@botfeeder.ca

                  Enhanced Spool Holder

                  1. Method: Drop from 1.2m in height
                  2. Number of Drops : 10 drops
                  3. Result: Passed

                  Drop Test from height of 1.2 meters

                  Certifications

                  To take an extra step for your safety, BotFeeder 3D Printer Filaments are being tested on an annually basis by SGS. On top of that, all our filaments are manufactured in compliance of RoHS (Restriction of Hazardous Substances).

                  SGS Certification

                  Material Science

                  BotFeeder was founded as a brand of Liing Shian Colorant Manufacturer which have been active in the masterbatch, and pigment & chemical auxiliaries for the plastics processing industry. Our knowhow, network and partnerships is driving material innovations and quality. You can expect BotFeeder to keep on developing interesting new materials, which will be tested on a variety of printers to make sure it’ll get the job done.

                    Sold Out

                    BotFeeder neoPLA Filament Aurora Pink 1.75mm

                    Caution! This intense pink will bring you into the center of attention in the public.

                    1. Brand: BotFeeder
                    2. Material: neoPLA
                    3. Diameter: 1.75mm
                    4. Colour: Aurora Pink
                    5. Filament Weight: 1kg
                    6. SKU: 0000
                    7. Made in: Taiwan

                    Specifications

                    1. Material Grade: NatureWorks 4032D
                    2. Diameter Tolerance: +/- 0.03mm
                    3. Roundness Tolerance: +/- 0.05mm
                    4. Spool Length x Width: 190mm x 85mm
                    5. Spool Hole Diameter: 38mm

                     

                    Tricks & Tips

                    At BotFeeder we have a well equipped 3D printing studio with a lot of popular 3D printers. We know our materials will give you excellent results and to help you get these results here are tips and trick for using BotFeeder 3D printing filament.

                    1. Extrusion Temperature: 190 to 210C
                    2. 3D Print Speed: 15 to 100mm/sec
                    3. Print Bed Temperature: 60 to 70C
                    4. Layer Thickness: 0.05mm or higher
                    5. Nozzle Size: 0.1mm or higher

                    Build Platform:
                    For BotFeeder neoPLA we advice to print on a heated bed. After printing, the build plate needs to cool down to about 20-30 C at which point you can remove the printed part.

                    In the Box

                    1. 1 x 1kg of BotFeeder neoPLA 1.75mm Aurora Pink Filament
                    2. 1 x BotFeeder spool holder
                    3. 1 x A pack of large desiccant
                    4. 1 x Vacuumed sealed bag

                     

                    Filament Care Tips

                    Storing Your Filament

                    Please note that improper storage may damage your filament. To maintain its original quality, it's strongly recommended that the filament be stored in the following conditions:

                    • A dehumidifier cabinet or a dry and circulated area
                    • Room temperature
                    • Avoid direct sunlight or heat source

                    Selecting A Printer Location

                    Please note poor printer location will have a negative effect on your print result and possible of damaging your filament. To select the most ideal location for your printer, please follow this guide.

                    • Consistent temperature
                    • Stable air flow
                    • Away from furniture for safety

                    Avoid Tangling Your Filament

                    When unpacking, changing filament or unloading, It is strongly suggested to get a good grip at the end of the filament at all times in order to prevent tangling. The spool holder is specifically designed with 2 holes of each side, allowing you to secure the end of the filament by threading into it. or you can simply 3D print a "Filament clip" that is attached to the spool holder itself.

                    BotFeeder ABS Colour Code & Filament Tracker

                    If Filament Gets Damp

                    Dry it slowly in room temperature. Please note that heat drying the filament will damages its quality by making it become brittle. The preferred method of drying your filament is to put in a dehumidifier cabinet or in an airtight bag with a few packs of desiccants. It's recommended to maintain a humidity level of 25% or less.

                    Quality

                    In-House Production

                    All BotFeeder 3D Printer Filaments are produced in our own production facility, situated in the Taiwan. Since no external parties are involved in the making of BotFeeder filament we can ensure consistent quality on every order.

                    Excellent Diameter Tolerance

                    An important machine in our production are the laser measurement systems used to check the diameter of our filament real time during production. It’s measured over 1000 times per second and helps us guarantee that each spool of BotFeeder 3d printing filament produced within tolerance. We can guarantee 0.03mm +/- on both 2.90mm and 1.75mm BotFeeder 3D Printer Filament, which means you can rest assured that your printer is extruding the exact amount of material.

                    Packaging

                    Within minutes of production a spool of BotFeeder 3d printing filament is wrapped with a protective film and then sealed airtight with a double barrier foil. To ensure minimal moisture, we upgraded to a large pack of desiccant.  To go the extra mile, we’ll also seal the fancy cardboard box that we use to ship our product. You can make sure BotFeeder 3d printing filament is fresh and ready for 3d printing when you’re done unboxing.

                    BotFeeder Filament Protective Measures

                    BotFeeder Filament Packaging

                    In-House Testing

                    The BotFeeder Testlab features a wide range of popular 3D printers. We’re continuously testing on our 3D printers to keep checking the quality of the materials we produce and to develop exciting new materials for the maker community. If your not sure how to print with our materials on your 3D printer, please contact us at support@botfeeder.ca

                    The following printers are used in our lab

                    • Ultimaker Original
                    • Ultimaker 2
                    • Makerbot Replicator 2X
                    • Lulzbot Mini
                    • Original Pursa I3
                    • Solidoodle 3
                    • UFO Standard (Delta & E3D hot-end)
                    • Rapidbot 2
                    • 3D Lounge PRO XL

                    Companies who are interested in having their 3D printer(s) featured in our testlab can contact us at support@botfeeder.ca

                    Enhanced Spool Holder

                    1. Method: Drop from 1.2m in height
                    2. Number of Drops : 10 drops
                    3. Result: Passed

                    Drop Test from height of 1.2 meters

                    Certifications

                    To take an extra step for your safety, BotFeeder 3D Printer Filaments are being tested on an annually basis by SGS. On top of that, all our filaments are manufactured in compliance of RoHS (Restriction of Hazardous Substances).

                    SGS Certification

                    Material Science

                    BotFeeder was founded as a brand of Liing Shian Colorant Manufacturer which have been active in the masterbatch, and pigment & chemical auxiliaries for the plastics processing industry. Our knowhow, network and partnerships is driving material innovations and quality. You can expect BotFeeder to keep on developing interesting new materials, which will be tested on a variety of printers to make sure it’ll get the job done.

                      Sold Out
                      Items 1 to 10 of 10 total
                      Safe Minimized VOCs & UFPs that poses health risks during 3D printing.
                      Ultra Precision Tight tolerance to ensure highest quality print achievement with no down time.
                      Innovative Strive to continue developing world-class products.
                      Vibrant Colours Over 50 attractive colours for all of your amazing creations.
                      Need Help? Our filament specialist team is ready to answer your questions.
                      Hot Items
                      700g PLA Filament 1.75mm – Silky Pearl White
                      700g PLA Filament 1.75mm – Metallic Copper
                      1kg PLA Filament 1.75mm – Light Tan (Skin)
                      1kg ABS Filament 1.75mm – Gray
                      1kg PLA Filament 1.75mm – Caramel